Recently, I watched the news of the Fiji router k2 being taken by my aunt for free. I read the comments on the Internet. Although most of them felt that this boat was going to be turned over, there were quite a lot of people who bought it. In JD.com, the sales volume of k2 is nearly 100,000 in sales, and he can have more fire. As a digital lover, you can get free stuff, how can you not get on this boat? Give yourself a handful of reasons. I immediately set up a single dog in the east and picked up a k1 and a k2. There is also a comparison. Here spit the courier under the dog east, obviously made an appointment to the evening, the result waited for one night, to push the information to me at 2 o'clock in the evening said that due to the full demand of goods, tomorrow can be served. But at noon the next day to get a smooth delivery, courier is also quite large, and still have some weight in my hand, I have been to the dormitory from the West Gate of the school, hot I quickly fried, Hefei's weather to powerless spit. Open the express, found that there is no difference between the two off-package, on the k1 and k2 labeling, and the power of the box marked under the k2 box power efficiency, super signal, the last picture, on this goods, k2 is the same.
Open the package, found that the router is also quite large, than the tp-link I used before a big lap, more than 3 antennas, but this is not any eggs, the hostel did not open the tool to find a look on the Internet k1, K2 disassemble diagram
K1 disassemble diagram
K2 disassemble diagram
The configuration of the two is roughly the same, 64M DDR2 memory particles plus MTK (MediaTek) cpu --MT7620A+MT7612E, 16M flash memory, 2.4G, 5G dual PA , this configuration, destined to it is just a low-end router, However, after all, it is free, but also a bicycle. Most of Fifo's firmware on the Internet has a back door. It collects user data and uploads it to his server. Interested partners can check it out.
So do not say anything, immediately brush the router on the router, ASUS firmware, openWrt, Pandora, how to brush on how to brush, relay, broadband overlay, a variety of fun and useful features, not write about Brush, Aunt on There are quite a few buddies already have tutorials.
Smart routing is now the most concern is the heat problem, should be a high temperature, it will lead to stuck card, suspended animation, restart to solve the problem, k1 has a ceramic heat sink, but it is recommended to be replaced by pure copper, so The effect of heat dissipation will be better, k2 on a large area of ​​aluminum + silicon thermal mud heat dissipation, it stands to reason that the heat should be a little better k2, the results when I power at the same time four children found that the temperature of k1 should be lower, I think it should be Is the k1 shell to do more open, hollow design allows him to have better heat dissipation, and the k2 shell is relatively closed, only the bottom of the hollow space, the other is a sealed shell, resulting in its internal temperature is not easy to escape .
The important point is that since the configuration of the two is the same, the only difference is the signal problem of the two. K2 is better than the signal of k1. To be stable, I will do a comparison in the bedroom and the software used is more mainstream. Wifi signal testing software WirelessMon . Below is a map of our bedroom. Our bedroom is roughly 20 square feet. Two routers are placed on the table opposite my friend at the same time. The signal strength of the four points is tested separately. The bathroom and balcony are tested to close the bathroom door. And the glass door of the balcony, make a confined space test, measure its ability to penetrate the wall.
The first is the stability of the signal. This is the measurement of its signal stability at my location.
K1 signal stability over a period of time
K2 signal stability over a period of time
This does not require the use of statistical software for analysis. It is straightforward to determine the stability of their signals. Obviously, k2 is better than k1. Here are the data I measured on four points
K1 test point 1 signal
K1 test point 2 signal
K1 test point 3 signal
K1 test point 4 signal
K2 test point 1 signal
K2 test point 2 signal
K2 test point 3 signal
K2 test point 4 signal
Through these two rounds of the two points of test, the data of the two changes all the time, the signal in the bathroom is the worst, the signal of k2 is -54dBm, the signal of k1 is -60dBm, the signal value k2 of the other three places is good At k1, this should explain some problems. The k2 signal is indeed better than k1. All of the above measurements are measured under 2.4g. My old book does not support 5G signals, and there is a rush of impulse. My ipad is supporting 5G signals, but there is no measurement tool, Nymar, so 5g is not tested. In addition, a fun feature on the map is the signal channel problem. The sharp-edged partner should have already seen the rough, k1 router, the more moving channel 1 is getting more and more crowded. In k2, the more it moves, the more crowded the channel 11 is. With a lot of routers here, with this, you can choose a less crowded channel to use.
Conclusion All the assessments are over here. There is something wrong with them. Although the young friends have correctives, the newcomers will post their posts for the first time, and they hope that everyone will support them.
Ring And Fork Type Insulated Terminals
Ring And Fork Type Insulated Terminals,High quality insulated terminal,copper tube terminal
Taixing Longyi Terminals Co.,Ltd. , https://www.txlyterminals.com