Length and width of the total call for renewals, the widow on the network no too high demand, usually just WOW and D3 no other needs, the previous renewals are selected barley box, but also filial piety to elders entertainment, the renewals 1,700 years, the first 4 years called 100M Bandwidth, after 6 years of 15M bandwidth, attached to the selected barley router, is the goods
Flat lay
Kikube
There will be LED light of faith after power on.
Picture quoted from Digital House
This particular model is configured as DW22D
CPU : MT7620A + MT7610EN;
Winbond's 128MB DDR2;
Winbond 16MB flash memory;
4LAN, 1WLAN, 1USB, 1SD (built-in TF)
Power Supply: 5V 2A
There are other types of NAND pads on the Internet, it is estimated that you can DIY, there are flash cards, I heard that is used to do the loading of the cache video, this section regrets that there are memory cards are also wood pads, Although it was white, I felt I was losing.
Although not tossing and uncomfortable, but in fact there is not too much hands-on ability, check the information on the Internet, this section routing configuration is not bad, you can brush;
The more popular are the following:
Brush millet, but because the 5G chip is different, the brush has a 5G signal to the wood, and the mobile phone APP is available. The plug-in is available but the relay mode is relatively miserable;
Brush routing, the available firmware is only 2, you can download it on the official website, but need to pay attention to the model, can only fit HC5761, the official website has two kinds of HC5761A and HC5761, the difference is that CPU with A is 7628A, without A The CPU uses the 7620A. The two CPUs are different. They really did not dare to experiment. Only the HC5761 was used, but the plug-in could not be used.
Lenovo's newifi, this also did not 5G, and support has been eunuchs, not recommended;
Lao Maozi (hungry Ross, a god horse organization like it, I do not understand) based on Asus RT-AC51U revision, I heard that it is very Niubi, and it seems very complicated, and resolutely gave up;
Finally select the latest version of the HC5761-sysupgrade-20160614-0fca9721.bin firmware downloaded from the official website;
There are many brush tutorials, but they are better than they are. The basis of the widow's 0 is to touch the stones and cross the river. The river has finally passed, so write this article to give future generations a shortcut. The main tutorials come from the two forums. , Digital House, Ensan wireless; checked a lot, originally thought that can be the same as before Fiji's routing does not need to open can brush, remembrance, frustration can only choose the ttl Brush. equipment is as follows, fortunately, cheap, with DuPont line, selected male to female. Baby can be downloaded in the description of the drive, the machine WIN10, 64-bit implementation of the implementation of the exe;
Then follow Enshan's tutorial to start the operation, but because of my understanding of no limit, according to this tutorial, still stuck for a few hours; the following simple combing:
The first step: download the relevant software here is mainly used SecureCRT, Tftpd32 (the two software Baidu can) and download Ensan hackpascal God of Bootloader-breed, with this we can be free to brush machine, specific download breed -mt7620-reset13 and Breed Enter.exe, because this is only suitable for this barley route, put the file called breed-mt7620-reset13 in the same directory as Tftpd32, easy to upload, of course, you can change the name, the tutorial was changed to B.bin This is more convenient;
The second step: welding ttl, note that only welding txd, rxd, gnd, do not weld vcc, I do not know why, the tutorial is written like this, pay attention to the USB small board and routing corresponding to the definition is the same, that is, routing Txd connected to the small board txd, is to reverse the output of the SecureCRT troubled me for a long time, after the router connected the USB board, connect the USB board with the computer;
Picture quoted from Ensan Wireless Forum
The third step: set the computer: local IP: 10.10.10.3 mask: 255.0.0.0 gateway: 10.10.10.123, connect the router and the computer with a network cable, any LAN port can be, the router boot;
The fourth step: start Tftpd32, so that after the start of the default FTP server address is 10.10.10.3, after opening it just fine, do not close oh;
Picture quoted from Ensan Wireless Forum
The fifth step: start SecureCRT, select the protocol Serial, port ttl to USB port, the widow is COM3, please prevail in each case, baud rate select 57600, cancel RTS / CTS option, click on the connection, this time if Under normal circumstances, SecureCRT will show that the connection is successful but there is no output. (Here it is because the USB mini-board and the routing connection have reversed the card for a long time. Finally, holding on to the belief, the result is reconnected once. OK) At this point, the route will be powered off and then restarted . After the restart, the SecureCRT will display the relevant options. Press the number 9 key on the keyboard before the end of 5 seconds to enter the TFTP mode. Wait for a moment and it will prompt "Input Uboot filename (). ==:" At this point enter the name of the Breed file just changed, if the connection is normal will start automatically upload and brush;
Picture quoted from Ensan Wireless Forum Picture quoted from Ensan Wireless Forum
Picture quoted from Ensan Wireless Forum
Step Six: The front just brushed into the breath This is just a bootloader, brush it and later brush other firmware will be more secure, breath after all known as "immortal". Next open BreedEnter.exe and click the start button;
Picture quoted from Ensan Wireless Forum
Picture quoted from Ensan Wireless Forum
Step 7: Open the browser and enter 192.168.1.1, enter the breast's management interface, select the firmware update, upload and restart the downloaded 2nd firmware, wait for a moment, and restart the route. At this point, the barley becomes a polar route 2 .
Picture quoted from iHandle's Sina Weibo
Why do you want to brush? The first is to do the original barley routing is anti-human, only supports dial-up and specify the IP, support U-disk is only to provide network access, the interface is good, the function is completely bright;
Brushed the pole 2, although there is no way to use plug-ins, but at least provide normal routing of the function. Here to Tucao pole routing strategy, to provide a rom will not rain it accounted for? Other routing brush your rom not Is it also a promotion? Why not use plug-ins? You don't need to provide after-sales service!
Forgive me for the late lazy cancer, most of the pictures are downloaded, only the first two are my own shot ... In fact, did not intend to write this, and later found worth buying wood has introduced big sell routers, and hastily wrote This immature text, you make do with it.
500 Portable Power Station,Lifepo4 Portable Power Station,Economical Portable Solar Power Station,Portable Power Station For Camping 500W
Jiangsu Zhitai New Energy Technology Co.,Ltd , https://www.zttall.com